Gea Plate Heat Exchanger GEA VT04 Plate For Plate Heat Exchanger. $50.00-$200.00/ Set. 10 Sets (Min. Order) 12 YRS CN. Supplier. Contact Supplier. Compare. Ad. Add to Favorites.
Four Reasons to Use GEA s Brazed Products GEA PHE Systems heat exchangers have significant advantages. 1. Smaller Size - GEA PHE Systems heat exchangers are 20% to 60% smaller than traditional shell & tube and coaxial type devices. This means they use less space, weigh less and require less refrigerant charge. 2. Flange Connections & Fittings - GEA engineering for a The hygienic flange connection (ASK) can be ordered either as a complete connection including bolts and nuts (ASK) or a hygienic groove flange (NFK)/hygienic flange (BFK) as a connection fitting on a vertical port. If a complete connection is ordered on a housing vertical port, the groove flange is welded onto the housing.
4 x G1 ½" female thread Male threaded, soldered and SAE connections are also available as options. Pipes must be connected so that the connections are stress-free. Linear expansion and vibrations from the pipes to the heat exchanger must be avoided. Raccords (standard) HYDAC HEX S400:4 x G ¾" taraudage HYDAC HEX S610 und HYDAC HEX S615:4 x Gelötete Plattenwärmetauscher Brazed Plate Heat 4 x G1 ½" female thread Male threaded, soldered and SAE connections are also available as options. Pipes must be connected so that the connections are stress-free. Linear expansion and vibrations from the pipes to the heat exchanger must be avoided. Raccords (standard) HYDAC HEX S400:4 x G ¾" taraudage HYDAC HEX S610 und HYDAC HEX S615:4 x
162 GPM STAINLESS STEEL BRAZED PLATE HEAT EXCHANGER J. Little Mercer Co. Stock Number:G-3332 Mfg. Alfa Laval. Richmond, VA Model CB76-30H(D21. D21) rated for 495 psi& 319 to 437 deg. F Stainless Steel-Copper Brazed. No gaskets required(4) 2 inch flanged in& out. 1.25 gallon volume each side Suitable for all non-corrosive refrigerants. UL Listed 3B 13. Plate Heat Exchangers - HYDACCopper brazed plate heat exchangers are pressure resistant up to 30 bar, 4 x G1" female thread HYDAC HEX S722:4 x G1½" female thread HYDAC HEX S522:4 x G1½" female thread Male threaded, soldered and SAE connections are also available as an option. The pipes must be connected so that connections are stress-free.
Copper brazed plate heat exchangers are pressure resistant up to 30 bar, 4 x G1" female thread HYDAC HEX S722:4 x G1½" female thread HYDAC HEX S522:4 x G1½" female thread Male threaded, soldered and SAE connections are also available as an option.Water heater The pipes must be connected so that connections are stress-free. Plate Heat Exchangers - Livingston & HavenCopper brazed plate heat exchangers are pressure resistant up to 30 bar, 4 x G1" female thread HYDAC HEX S722:4 x G1½" female thread HYDAC HEX S522:4 x G1½" female thread Male threaded, soldered and SAE connections are also available as an option. The pipes must be connected so that connections are stress-free.
Stacked, corrugated plates maximize contact with liquid or steam flowing through these brazed plate heat exchangers for faster heat transfer than shell and tube heat exchangers. Plates are brazed in a vacuum furnace to ensure 100% sealed construction.. Copper-brazed heat exchangers have a Btu/hr. cooling capacity based on cooling water from 120° to 100° F using 70° F water.
Your email address will not be published.*